Grounding and Bonding Network Racks: A Maintenance Primer

A maintenance director who has worked in a building for a decade will tell you the odd things in a data closet are never the equipment. They are the green wire that goes nowhere, the copper bar bolted to the wall with nothing attached, or the rack that gives a tingle when you touch it. Those clues point to grounding and bonding, a topic that is easy to ignore until it causes trouble.

This article is a primer for understanding what to look for. It is not a substitute for a licensed electrician, and electrical work on a rack should be done by qualified people following your local code and the equipment maker's instructions.

What grounding and bonding mean

Grounding connects a system to the earth, usually through the building's electrical service, so that stray electrical energy has a path to go. Bonding joins metal parts together so they sit at the same electrical potential, which means there is no voltage difference between them for a person or a device to bridge.

In a network closet, the metal rack, the cable trays, the shielded cable ends and the equipment cases should all be bonded to one another and to the building's grounding system. The purpose is safety and reliable operation. It reduces shock risk if a fault energizes a metal part, and it helps surges and static find a controlled path instead of passing through your equipment.

Why racks and shields matter

Some network cables have a metal shield around the wires to reduce interference. A shield only works if it is connected to ground properly at the right points. A shielded cable that is not bonded can act as an antenna, and one bonded poorly can create a loop that carries unwanted current.

Racks are large metal objects that touch many pieces of powered equipment. If one device develops a fault, the rack can become part of the path. A good bond keeps the rack at a safe potential and gives protective devices on the circuit a chance to trip.

Neither is something to improvise. The correct design depends on whether your cabling is shielded or not, the building's electrical system and local code.

What an inspection should look for

You do not need a meter to spot many problems. Walk the closet with a flashlight and look for:

A grounding conductor, typically a heavy insulated copper wire, connected to the rack and running toward a grounding bar or the building's grounding point.

A grounding bar in the closet, if the design calls for one, with clean, tight connections and labels.

Connections that are tight, free of corrosion, and not made with a painted surface under the lug. Paint can prevent a good metal-to-metal contact.

Rack-mounted equipment mounted securely with appropriate hardware, so the case is bonded to the rack where the design relies on it.

Cable trays and any metal conduit that are joined together and bonded.

No obviously cut, taped or loose ground wires.

Three-prong power plugs whose ground pin has not been removed or defeated with an adapter.

If anything seems wrong, photograph it and report it. Do not tighten or reroute grounding conductors yourself unless you are qualified.

Signs of a grounding problem

Some symptoms are worth taking seriously, even if they seem minor.

A mild shock or tingle when touching a rack or a metal case.

Equipment that behaves strangely during storms or when large motors start.

Frequent, unexplained errors on a particular run or device that cannot be traced to cabling or settings.

Scorch marks, discoloration or a burning smell near power equipment.

A tingle is a reason to stop and call an electrician right away.

Who does what

Planning and testing usually involve several people. Your maintenance director knows the building's electrical layout and the history of changes. A licensed electrician installs and verifies the bonding, and may measure resistance to the grounding system. Your cabling contractor or IT provider confirms that the cabling design, especially any shielded cable, is terminated as the manufacturer requires.

Ask for a written record of who did the work and how it was checked. Local codes and standards govern the details, and your electrician or the relevant authority can tell you what applies to your building.

Keep it in the maintenance routine

Add the closet to your regular rounds. Check the grounding connections after any construction, rack move or electrical work, since those are the moments a ground wire is most often disturbed. Note the findings, with the date and the initials of the person who looked.

How we can help

UnityCare IT can include grounding observations in a closet review, flagging what looks unbonded or unlabeled so your maintenance director and electrician can take it from there. We coordinate with your electrician and cabling contractor so the network design and the electrical work agree.

Related service

Wi-Fi, switching, firewalls and internet that hold up across a whole facility.

Related articles

Keep reading

Contact UnityCare Technologies

Call or text: 405-285-3845

New customers: start@unitycareit.com

Existing customers: support@unitycareit.com

Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas

Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support