Latency, Jitter and Packet Loss: Three Numbers Behind Bad Calls

The speed test says the connection is excellent. Yet the physician on a video visit sounds like a robot, the phone call to a family member keeps clipping, and the provider's report shows nothing wrong. Staff say the internet is bad, and the provider says it is fine.

Both can be true. Speed measures how much data can move. Calls depend on three other things, and your provider's report may include them.

Speed is not quality

Think of a highway. Speed, or bandwidth, is the number of lanes. A wide highway carries a lot of traffic. But a phone call is less like a freight convoy and more like a stream of small packages that must arrive quickly, in order and all of them.

A wide road with a long detour, uneven delays and missing packages is still a bad road for conversation. Those three problems have names.

Latency

Latency is the time it takes for data to travel from your building to somewhere else, and often back. It is measured in milliseconds, which are thousandths of a second.

Some delay is unavoidable, since distance matters. But when latency is high, there is a lag in conversation: people talk over each other, pause too long, and say "go ahead" repeatedly. On a video visit, the doctor sees the resident a beat behind.

Causes include long routes, overloaded equipment, a satellite or wireless link and a connection that is busy with other uses.

Jitter

Jitter is variation in latency. If each packet takes exactly the same time, the call is smooth even if the delay is somewhat long. If one packet takes a short time and the next takes a long time, they arrive unevenly, and the audio stutters or speeds up.

Jitter is often the cause of calls that start well and get choppy. It commonly appears when the connection is sharing with a big download, a backup running in the middle of the day, or when Wi-Fi is weak.

Packet loss

Packet loss is the share of packets that never arrive. Small amounts may not be noticeable for browsing, because the computer simply asks again. For voice and video there is no time to ask again, so the missing piece becomes a gap, a robotic sound or a frozen frame.

Causes include a bad cable, a faulty connector, a failing device, a weak Wi-Fi signal, a congested link or a problem on the provider's line. Loss that comes and goes can be especially hard to find.

How to read a provider's report

Ask your provider for a report that shows more than speed. Look for:

Latency to a nearby point and to a distant one, with average and highest values.

Jitter, usually given in milliseconds.

Packet loss, given as a percentage of packets.

The time of the test. Problems that appear at the busy 10 a.m. hour may be missing from a test at midnight.

Where the test ran. From the provider's box or a computer inside, by cable or on Wi-Fi.

Generally, lower numbers are better for all three, and zero loss is the goal. There is no single threshold that applies to every phone system or video product. Ask your phone or telehealth vendor what they recommend, and compare your report against that.

Narrowing down the cause

When calls break up, try these steps in order:

Does it happen only on Wi-Fi, or on a cabled computer too? If only on Wi-Fi, the problem is wireless coverage or interference.

Does it happen at certain times? Check for backups, updates or heavy use then.

Does it happen in one room or all rooms?

Does a short test show loss when connected directly to the provider's box? If so, the provider's line needs attention.

Does it happen to one system, or all?

Write down dates, times, locations and what was happening. A record like "Tuesday 10:15 a.m., hall B, three calls choppy" is far more useful than "the internet is bad."

Ways to improve

Prioritize voice and video on your firewall so they go first. Move backups and updates to the night. Replace damaged cable. Add or retune access points where Wi-Fi is weak. Ask the provider to investigate the line if loss shows up at the box. If trouble continues, consider a second connection.

How we can help

UnityCare IT measures latency, jitter and packet loss in care buildings, and translates the report into plain terms. We prioritize voice and video traffic, correct cabling and Wi-Fi faults, and work with your provider when the problem lies on their side. Our help desk can start the investigation after hours.

Related service

Wi-Fi, switching, firewalls and internet that hold up across a whole facility.

Related articles

Keep reading

Contact UnityCare Technologies

Call or text: 405-285-3845

New customers: start@unitycareit.com

Existing customers: support@unitycareit.com

Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas

Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support