Network Requirements for Security Cameras and Video Recorders

The maintenance director has a quote for sixteen new cameras, and the installer says they will "just plug into the network." Then the Monday morning charting slows down, the recorder shows gaps in video and nobody can view the lobby from home. The cameras worked on installation day. Nobody asked what they would do to the network once all of them were recording at once.

Security cameras are a steady, heavy load on the building network. They send video all day and night, whether anyone is looking or not. Planning for that load is not complicated, but it must happen before the cameras go up.

What each camera adds

Every camera has a few needs.

A switch port. Each camera takes one wired port, usually on a switch in a network closet.

Power. Most cameras get power through the same cable using Power over Ethernet (PoE). That means the switch must have enough total power budget for all the cameras attached, not just enough ports.

A cable run no longer than about 100 meters (roughly 328 feet) from the switch. Farther cameras need an intermediate switch or fiber.

Bandwidth. A camera streams video continuously. Higher resolution, higher frame rate and more detailed scenes mean more data. A busy hallway generates more than a blank wall.

The amount varies by model and settings, so ask the installer for the expected data rate per camera and add them up.

Resolution, recording and storage

Higher resolution gives sharper images but costs bandwidth and storage. A camera watching a parking lot or a front door may deserve high resolution, while one in a back corridor may not.

Recording choices also matter. Recording all the time uses far more storage than recording only when motion is detected, but motion recording can miss events or start late. A network video recorder (NVR) stores the video, and its disks must be large enough for the retention you want. How long to keep footage is a policy decision that may be influenced by your insurer, state rules or an internal policy, so confirm those requirements before you size the storage.

The video traffic itself travels from each camera to the recorder. If the recorder sits on the same network as everything else, that traffic competes with charting and phones. Putting the cameras and recorder on their own network segment, with their own switches where practical, keeps video from crowding clinical traffic.

Remote viewing the safe way

Managers want to check a camera from home. The risky way is to open a port on the firewall so the recorder can be reached directly from the internet. Recorders exposed that way are commonly found and attacked. A safer approach is to connect through a secure remote-access method that does not publish the recorder, such as a VPN or a vendor-neutral secure gateway your IT provider manages. Remote viewing also uses the building's internet upload speed, so a few simultaneous viewers can strain a slow connection.

Also change default passwords, keep recorder software updated and limit who has accounts.

A planning checklist

Count the cameras and note their resolution and where each will be mounted.

Confirm each location has a cable path no longer than the limit, or plan an extra switch.

Add up the PoE power the cameras need and compare it with the switch's budget.

Confirm the switch uplink between closets can carry the combined video.

Size recorder storage for your chosen retention and recording mode.

Place cameras and recorder on a separate network segment.

Decide how remote viewing will work and who gets access.

Plan power backup for the recorder and switches, so video does not vanish when the lights flicker.

Privacy and placement

Where cameras may point, what must not be recorded and whether audio is allowed are legal questions that depend on your state and on resident privacy rights. Rooms where residents receive care and bathrooms need special caution. Check with counsel and your state association before finalizing placement. This article covers the network side only.

How we can help

UnityCare IT installs and supports security cameras and the network behind them across Oklahoma, Texas and Kansas. We size switches, power, storage and remote access before the first camera is mounted, and we keep video traffic off your clinical network. We can also review an installer's quote from another company.

Related service

Wi-Fi, switching, firewalls and internet that hold up across a whole facility.

Related articles

Keep reading

Contact UnityCare Technologies

Call or text: 405-285-3845

New customers: start@unitycareit.com

Existing customers: support@unitycareit.com

Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas

Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support