It is a Saturday in July, the air conditioner serving the back hall quietly stops working, and the small room that holds the network switches begins to warm up. Nobody goes into that room on a weekend. By Sunday afternoon, equipment is shutting itself down, and by Monday the day shift finds the charting system unreachable.
A temperature and humidity sensor in the equipment room costs little compared to the downtime it prevents. It gives you a warning while a problem is still a maintenance ticket, not an outage.
Network equipment gives off heat all day. In a small closet with a door, little ventilation and a ceiling full of warm air, that heat has nowhere to go. Rooms that share space with a water heater, a laundry exhaust or a storage shelf stacked against the vents are the worst candidates.
Humidity matters too. Air that is too humid can lead to condensation and corrosion over time, and air that is very dry increases static electricity. Closets near kitchens, laundry or a leaky roof deserve extra attention.
A sensor does not cool anything. It tells someone, in time, so they can act.
Placement is where most installations go wrong. A sensor hung on the wall near the door tells you about the hallway.
Put the main sensor near the air intake side of the rack, at about the height of the equipment, since that is the air the equipment is breathing.
If the rack is tall, add a second sensor near the top, because warm air rises and the top of a rack often runs hotter.
Keep sensors away from the air conditioning vent, which would show the coldest air in the room, and away from the exhaust of the equipment.
In a room with more than one rack, put at least one sensor on each.
Consider a separate sensor on the floor if the room has any chance of water, such as a pipe overhead or a drain nearby. A water leak sensor is a different device and often worth having.
Mount them where they will not be knocked off by a cleaning cart or covered by a box.
Equipment manufacturers publish the operating temperature range for their products, so the first step is to check what your gear is rated for. Your IT provider can look this up. Then set alerts with a warning level well before the limit, and a critical level closer to it.
A sensible approach has two tiers:
Warning: the room is warmer than usual, well inside the safe range. This should reach a person during business hours and prompt a look at the cooling.
Critical: the room is approaching the limit for the equipment. This should wake someone up, because the next step is shutdown or damage.
Set humidity alerts in the same way, for both a high and a low reading, using the manufacturer's guidance. Also alert on a fast rise, even if the number is still in range, since a jump of several degrees in an hour signals a cooling failure in progress.
Avoid setting the warning so tight that it fires every afternoon, because people will start ignoring it.
An alert that goes to a shared inbox no one reads is not an alert. Decide who is responsible at each hour.
The maintenance director, because the fix is almost always air conditioning, ventilation or a leak.
The administrator or the administrator on call, so they know a system may be at risk.
Your IT provider, so they can check that equipment is healthy and shut down gracefully if needed.
For weekends and nights, whoever is on call, by text message or phone call and not email only.
Write down the response: who walks to the room, who calls the heating and cooling contractor, and what temporary steps are acceptable, such as propping the door or placing a fan. Confirm with your maintenance director that a temporary fix is safe and does not compromise fire doors.
Test the alert path every few months by warming the sensor gently or using the device's test function, and confirm that the right people actually got the message. Replace batteries on schedule if the sensor uses them. When your internet or network goes down, a sensor that relies on the network to send alerts may go silent, so ask whether it has a cellular option or a second path.
UnityCare IT can recommend and install environmental sensors in your closets, set sensible thresholds for the equipment inside, and route alerts to the right people, including after hours. We can also review the room itself, its cooling and layout, and suggest changes before heat becomes an outage.
Wi-Fi, switching, firewalls and internet that hold up across a whole facility.
Call or text: 405-285-3845
New customers: start@unitycareit.com
Existing customers: support@unitycareit.com
Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas
Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support