The facility sits between a strip of shops and an apartment complex. Wi-Fi works well at 6 a.m. and gets sluggish by evening, and nothing inside the building has changed. The wireless scan on a laptop shows dozens of networks, most of them belonging to neighbors.
Wi-Fi is a shared medium. Every network in range is using the same limited slices of radio spectrum, and when two networks use the same channel they must take turns talking. A channel plan is how you decide which access point uses which slice so they get in each other's way as little as possible.
Think of a channel as a lane. Devices on the same channel must wait for one another, even if they belong to different networks. A neighbor's router in the next apartment can slow your access point if both are on the same channel and loud enough to hear each other.
Wi-Fi runs mostly in two bands. The 2.4 GHz band reaches far through walls but has very few channels that do not overlap with each other (in the United States, channels 1, 6 and 11 are the usual choices). The 5 GHz band has many more channels, shorter range and faster speeds. Newer equipment may also use a 6 GHz band, which is even less crowded but has the shortest reach.
Outside networks get the blame, but a facility with a dozen access points often competes with itself. If neighboring access points in your own halls share a channel, or if each is set to maximum power, they interfere with one another and devices struggle.
Common self-inflicted problems include:
Every access point left on automatic channel selection, which can change channels during the day and drop connections.
Wide channels on 5 GHz that leave too few separate lanes for a building full of access points.
The 2.4 GHz band turned on for every access point, which creates a lot of overlap when only a few are needed.
Power set too high, so distant access points hear one another.
A good plan is tailored to the building, but the pattern is familiar.
Start with a survey. Measure what neighbors are broadcasting and how strongly, and record it at several times of day.
Use 5 GHz as the main band for staff devices and keep 2.4 GHz for older devices that need it, enabling it only on some access points.
Use narrower channels in dense areas. A narrower lane carries less data per device but allows more separate lanes, which is usually better in a building full of users.
Place neighboring access points on different channels and lower their power so each covers its own area.
Be careful with channels shared with radar. Some 5 GHz channels must yield to weather and airport radar and may move unexpectedly. Ask your installer how they are handled where you are.
Set it, document it and recheck it after any building change.
Automatic channel selection is not always wrong. Many modern systems manage it well. The point is to confirm the system is behaving sensibly, rather than assume.
Sometimes the crowding is not from other Wi-Fi at all. Microwave ovens in a break room, wireless video baby monitors, cordless phones, certain wireless cameras and failing lighting equipment can all produce noise in the 2.4 GHz band. If the complaints cluster near the kitchen or break room, ask your IT provider to look for non-Wi-Fi interference with a spectrum analyzer.
When was the last wireless survey, and did it include the neighbors' networks?
Are channels set manually or automatically, and why?
What channel width are we using on 5 GHz?
Is 2.4 GHz turned on everywhere, and does anything we own actually need it?
What changed in the building since the last survey?
You do not need to understand the answers in detail. You need to hear that someone has actually looked.
UnityCare IT surveys the wireless environment around care buildings, builds channel plans and checks them again when neighbors or floor plans change. We work across Oklahoma, Texas and Kansas and can adjust your existing equipment before recommending anything new. If the real problem turns out to be interference from a break room appliance, we will say so.
Wi-Fi, switching, firewalls and internet that hold up across a whole facility.
Call or text: 405-285-3845
New customers: start@unitycareit.com
Existing customers: support@unitycareit.com
Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas
Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support