A fire crew enters a new care building, and their handheld radios, which work everywhere else in town, go quiet inside the concrete and metal of the building. The incident commander at the door cannot hear the crew in the back wing. That is the problem emergency responder radio coverage requirements are meant to prevent.
If you are planning new construction or a major addition, this requirement can affect your budget and your schedule, so it is worth raising early.
Public safety agencies, such as the fire department, police and EMS, use radio systems with towers across the area. Modern buildings use energy-efficient glass, metal framing, concrete and foil-backed insulation, and those materials block radio signals.
Many jurisdictions have adopted fire code provisions that require a building to demonstrate adequate signal strength for responders' radios inside it. When the outside signal does not reach well enough, the building may need an in-building system to boost it, commonly an amplifier with antennas distributed through the building.
Whether your building must have such a system, in which areas, and to what signal standard depends on the fire code your jurisdiction has adopted, any local amendments and the decision of the fire official. Some areas have no such rule at all. Do not assume either way.
Ask your architect and your fire marshal, early in design:
Does our jurisdiction require responder radio coverage for this building type and size?
If so, what areas must be covered, such as stairwells, electrical rooms, the whole building or only certain floors?
What signal standard must be met, and how is it tested?
Which radio system and frequencies does our local agency use?
Do they require a pre-approval or a permit for the equipment?
Is a test needed before opening, and who witnesses it?
Record the answers in writing. If the answer is "it depends," ask for a pre-construction meeting.
If a system is required, it generally includes:
Antennas placed around the building, often in the ceiling.
Cabling between them, which can be a significant part of the work.
Amplifiers in a central equipment room.
Backup power, so that it works during an outage, and in some places a monitoring panel.
An outside antenna that picks up the public safety signal.
It resembles a Wi-Fi network in layout but uses different equipment and has different approvals. It is not a task for a general network technician. Most jurisdictions expect specialists with the right licensing to design and install it, and you should ask your local authority about that.
Costs depend heavily on the building's size and materials, so get quotes rather than guessing. Include:
A pre-construction survey or test of the signal at the site, ideally before the walls go up.
The design, equipment, installation and permit fees.
Backup power and any monitoring connections.
Testing, and a retest if the first attempt fails.
Ongoing maintenance and periodic testing, which fire officials may require.
The cheapest time to plan for it is during design. Cable pathways, equipment room space and power can be included in the building plan. Adding it after the building is finished costs more and may require opening ceilings.
Testing usually involves walking the building with a signal meter or a radio, sometimes using a grid of areas on each floor, and recording the results. The authority sets pass or fail criteria. Results are often needed to receive the certificate of occupancy, so they can affect your opening date.
Ask who will schedule the test, who is responsible if the building fails, and how long a fix takes. Allow some time in the schedule for a retest.
The responder radio system should be coordinated with fire alarm, electrical, and your IT provider's cabling. It shares ceiling space and power with other systems, and should not be forgotten when you decide jack counts and closets. Do not confuse it with your staff's own radios or Wi-Fi handsets, which have separate needs.
UnityCare IT plans the network side of care construction projects, including closets, pathways and power, and coordinates with the specialists who design responder radio systems. We help you ask the right questions early and keep the documentation. Code requirements themselves should be confirmed with your fire marshal and architect.
Wi-Fi, switching, firewalls and internet that hold up across a whole facility.
Call or text: 405-285-3845
New customers: start@unitycareit.com
Existing customers: support@unitycareit.com
Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas
Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support