A summer storm rolls across the property, and by morning the east wing's phones and computers are offline. The cable that ran across the parking lot to the main building took a lightning strike. The equipment at both ends is damaged, and it is not just the cable that needs replacing.
When two buildings are connected by a copper network cable, the cable becomes a path for electricity as well as data. Fiber does not have that problem, which is the main reason it is the right choice between separate buildings.
Ordinary network cable is made of copper wires. A copper run between buildings can carry a surge from lightning or a nearby power fault from one building into the other. It can also pick up differences in electrical ground between two structures, which causes strange, intermittent faults that are hard to trace.
Copper also has length limits. Standard network cable is designed for a limited distance, and a run across a large lot, or between far corners of a campus, may exceed it. Outdoor exposure to sun, moisture and temperature swings shortens its life as well, unless it is rated for the environment.
None of this means a short, protected run is always impossible. Electricians and cable installers sometimes use surge protection for specific situations. But for a permanent link that your building depends on, fiber is the more dependable choice.
Fiber optic cable carries data as light through glass strands, with no metal path for electricity to follow.
It does not conduct lightning or power surges between buildings
It is not affected by electrical noise or differences in ground
It can run much longer distances
It can carry far more data, so it will not limit you if you grow
Outdoor-rated types resist moisture and temperature changes
The equipment at each end still needs normal surge protection, but the cable between them no longer carries the hazard.
Fiber installation is not complicated, but it has several steps that affect cost and time.
Planning the route. Decide whether the cable will go underground in conduit, along poles or through existing pathways. Underground conduit usually protects best.
Locating utilities. Digging requires locating buried lines first. Your contractor should handle this, and it is generally a legal requirement to call before digging. Check with your state's one-call service.
Running the cable. Trenching or boring, or pulling through conduit that is already there.
Termination. Fiber ends are connected to panels and to small modules in the switches at each building, a job that needs special tools.
Testing. The contractor should test the finished link and give you the results.
Labeling and documentation. Each strand and panel should be labeled, with a map of the route.
Ask maintenance to flag irrigation lines, parking lot repairs and landscaping plans before the route is chosen.
A written quote that compares easily with others covers these items.
The route, the length and how the cable will be buried or run
The type of cable and the number of strands, with spare strands for the future
Conduit, trenching, boring, restoration of pavement or landscaping
The panels, connectors and modules at both ends, and whether they work with your switches
Testing, with a written report of the results
Labeling and a drawing of the route
Permits, utility locates and any required coordination
Warranty terms on materials and workmanship
A schedule, and what happens to service during the cutover
Ask how the work will be done without cutting off phones, nurse call and cameras on the day of the change, and who is responsible if existing lines are damaged.
Fiber cable carries several strands, and extra ones cost little compared with digging again. Having a spare pair lets you add a second link, a camera system or a door access network later. Ask your contractor to include spares. Also ask your IT provider whether a second route to a building, for backup, is worth considering for critical buildings.
Save the route drawing and test results with your building records. Years from now, when someone plans to dig a new sidewalk, those documents may prevent a cut cable.
UnityCare IT helps owners and maintenance directors decide how to connect buildings, review contractor quotes for fiber work and make sure the switches and equipment at each end are suited to the link. We can coordinate the cutover so phones, nurse call and cameras stay up, and we document the result. We work on site across Oklahoma, Texas and Kansas.
Wi-Fi, switching, firewalls and internet that hold up across a whole facility.
Call or text: 405-285-3845
New customers: start@unitycareit.com
Existing customers: support@unitycareit.com
Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas
Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support