The maintenance director mounts a new camera over the side entrance, plugs it into the closet switch and walks away. An hour later the front desk reports that two phones on the same switch keep rebooting. Nothing was wrong with the phones. The switch ran out of power to give.
Power over Ethernet, usually shortened to PoE, lets one network cable carry both data and electricity. It is why a phone, camera or Wi-Fi access point can be installed without a nearby outlet. It also means your switch is a small power plant with a fixed capacity, and every device you add draws from the same pool.
A PoE switch has two limits worth knowing about. Each port can deliver only up to a certain amount of power, which depends on the switch and the standard it supports. And the switch as a whole has a total power budget, measured in watts, shared among all its ports.
A 24-port switch does not necessarily have enough power to run 24 hungry devices at once. Many are designed on the assumption that most ports will use less than the maximum. If the connected devices together ask for more than the budget, the switch has to shed load. Depending on the model and settings, it may turn off a port, often the one most recently connected or the lowest priority, which is how a phone can drop when you add a camera.
Devices vary a lot, and the label on the box or the spec sheet is the place to look. As a general guide:
Basic desk phones tend to need a small amount of power
Wi-Fi access points usually need more, and newer, faster models often need more still
Fixed security cameras sit in the middle, but cameras with heaters, infrared lights, motors or zoom lenses can need considerably more
Door controllers, clocks, intercoms and some nurse call devices may also draw PoE
Cold weather can make this worse. A camera with a built-in heater may draw much more on a freezing night than it does in summer, so a budget that looks fine in the afternoon can fail at 4 a.m. in January.
You do not need to be a network engineer to ask the right questions. Ask your IT provider, or use the switch's management page, to find out the following.
What is the switch's total PoE budget in watts?
How much is being used right now, and what is the highest it has reached?
What does each connected device draw, and what is its maximum?
How much would the new device draw at its maximum, including heaters or lights?
How much margin will be left afterward?
A reasonable habit is to leave a cushion rather than plan to use every watt. Many installers keep some headroom for later additions and for peak draw. Ask your provider what margin they recommend for your building.
Several details cause surprises. The switch's budget may be lower than the sum of its ports, since the label on the front can promise more than the power supply can deliver. Switches in a hot, cramped closet may deliver less than their rating. Long cable runs lose some power. And cheap or damaged cables can cause a device to restart at random, which looks like a power shortage but is not.
Another trap is the quiet addition. Over a few years, a closet accumulates a camera here, an access point there and a new door reader. Each seemed small. The total was never rechecked.
If the numbers do not work, there are straightforward remedies.
Move devices to another switch with spare capacity
Replace the switch with one that has a larger budget
Use a separate injector for a single high-draw device
Set priorities so the most important devices, like phones and emergency equipment, are the last to lose power
Put key devices on a backup power supply in the closet, so a short outage does not drop them
Which fits depends on the building. A maintenance director can help by keeping a list of what is plugged into each closet and where.
Write down each closet, its switch, its power budget and what is connected. Update it whenever someone adds or moves a device. Whoever installs a camera or access point should check the list first. It costs a few minutes and avoids a call from the front desk.
UnityCare IT designs and supports care building networks, including checking switch power budgets before cameras, phones or Wi-Fi are added. We can document what is connected to each closet and recommend switch upgrades or backup power when the numbers get tight. Our team works on site across Oklahoma, Texas and Kansas and can install security cameras with the capacity in mind.
Wi-Fi, switching, firewalls and internet that hold up across a whole facility.
Call or text: 405-285-3845
New customers: start@unitycareit.com
Existing customers: support@unitycareit.com
Service area: based in Edmond, Oklahoma, serving Oklahoma, Texas and Kansas
Hours: Mon–Fri 8 AM–5 PM CT; 24/7 after-hours support